Amazon.nl: Klantenrecensies: GEEETECH PLA Silk filament 1,75 mm, 3D-printerfilament PLA 1 kg spool, wit, 1

Vertaal alle beoordelingen naar het Nederlands

Beoordeeld in Nederland op 18 januari 2022

Stijlnaam: Zijdegroen.Geverifieerde aankoop

Great accurate filament. Color is a little light buy that's okay.
Fiberlogy green silk has a more saturated green colour but not worth the extra costs over this Giantarm filament.

Nuttig

Vertaal recensie in het Nederlands

🍀✅🍀 𝓜𝓻. Paul 🍀✅🍀

🦄🦄🦄 Bonne adhérence, rendu parfait, Silver Gris, temp buse 205°, bed 60°🦄🦄🦄

Beoordeeld in Frankrijk op 10 oktober 2020

Stijlnaam: Silk Silk Silk SilkGeverifieerde aankoop

🔬Test de cette Bobine Geeetech Siver Gris Filament PLA 1.75mm

J'ai comme d'habitude fait le tour d'amazon pour essayer de trouver le meilleur rapport qualité prix, avant de tenter de choisir cet article.

Les + 👍:
- super adhérence plateau chauffé à 60°
- Après une tour de température pour moi c'est 205° pour la buse
- buse en 0,4mm
- Un rendu Brillant gris superbe
- filament bien calibré 1,74 mm à 1,77mm sur un test de 50cm
- filament parfaitement tenu à la bobine, ce qui évite la cata , à l'ouverture d'un sachet trop bousculé pendant les transport.
- une bobine bien enroulée, mais pas linéaire

Les - 👎:
- un filament qui n'est pas linéaire.

💰 Est-il selon moi un bon rapport qualité prix ?
👌 Un grand OUI

🌟Si vous avez aimé mon test, mon commentaire, un petit clic sur "commentaire utile" (c’est encourageant), vous pouvez vous abonner si vous voulez voir les autres tests🌟
Merci😽

46 mensen vonden dit nuttig

Vertaal recensie in het Nederlands

MULASKA

Top ! Farbeffekt über Temperatur regelbar !

Beoordeeld in Duitsland op 12 oktober 2019

Stijlnaam: blauw (silk royal blue)Geverifieerde aankoop

Meine Farbwahl war "Silky Royal Blue".
Für gewöhnlich Drucke ich PLA mit 200 - 210 °C.
Hier erschien der Druck aber eher als Blau Metallic. Zudem hatte ich den Eindruck dass das Material sehr "flüssig" ist.
Also bin ich Schrittweise mit der Temperatur runter gegangen.
Unter Verwunderung stellte ich fest, dass sich der Glanzeffekt durch die Temperatur regeln lässt ! Geile Sache !
205 - 210 °C - Hochglanz Metallic. Je mehr die Temperatur abgessenkt desto tiefer wurde der Blauton. Der Metalliceffekt schwächt minimal ab. Unter 200°C stellte sich dann der Seidenglanz-Effekt ein. Der "Sweetspot" war bei mir genau 197°C. Dann erhält man eine schöne seidig schimmernde Optik.

Da die Temperaturanzeige von Drucker zu Drucker schwankt, darf man mich nicht auf das Grad genau festnageln ;)
Alles in allem aber ein gutes Material!
Die Aufspulung könnte sauberer sein.
Das Abwickeln hat aber bisher noch keine Probleme bereitet.
GEEETECH hat einen neuen "Fan" gewonnen.

42 mensen vonden dit nuttig

Vertaal recensie in het Nederlands

Mark Smith

Another winner from Geeetech. SHINY!

Beoordeeld in het Verenigd Koninkrijk op 20 februari 2020

Stijlnaam: Silk GoldGeverifieerde aankoop

I purchased this Geeetech Gold Silk PLA filament to produce a Stargate themed cosplay hand ornament for a lady who contacted me on Facebook. After that was finished I decided to see the quality the filament could produce so I downloaded the STL for this low-poly vase from thingiverse.

The texture and sheen of the finished vase can't really be captured very well, but it looks and feel spectacular. I printed it on my TEVO Tornado at 0.15mm layer height, at 210/60 for the first 3 layers and then 195/40 for the remainder. I sliced it in Cura and used vase mode.

The 20CM tall vase took around 4 hours to print.

This is the umpteenth reel of Geeetech PLA I've purchased and I've been impressed with all of it.

9 mensen vonden dit nuttig

Vertaal recensie in het Nederlands

Samfish74

Beautiful colour and prints perfectly

Beoordeeld in het Verenigd Koninkrijk op 16 maart 2020

Stijlnaam: Silk GoldGeverifieerde aankoop

Im a firm believer in only buying filament over £20, a rule which came about after buying cheap filament and being frustrated for hours on end
So now I make a purpose of only buying stuff over 29
Ive bought a couple of Geetech rolls in the past mainly boring black and white, and I wanted something with a wow factor for a present and knew its what i needed
Straight from get go with 205 as nozzle temp and 65 at bed, it stuck brilliantly, no issues whatsoever
Made this very crisp vase (though ill admit my extrusion problems were present before and they're not as bad as usual with this filament)
I thought it might be glorified yellow but it really is a shiny gold! Really really happy with it!
Overall i have had lots of success with Geetech filament, and this is no exception, as far as brands ive tried, this seems to definitely be near the very top alongside Filaprint
Decent and affordable!

7 mensen vonden dit nuttig

Vertaal recensie in het Nederlands

Richard Thompson

Geeetech are fast becoming one of my favourite filament brands.

Beoordeeld in het Verenigd Koninkrijk op 24 november 2019

Stijlnaam: A Silk CopperGeverifieerde aankoop

So, after a good experience with the Geeetech White filament, I thought I'd give something sparklier a try.

This is an interesting filament, unlike most I've used it's pretty hard to snap off the reel. It adheres to my Prusa i3 Mk3S smooth PEI bed like nothing I've ever seen - I've taken to cleaning the bed less when using this or it can actually be hard to get parts off! If you just want a PLA to stick to the bed well, buy this and don't bother reading the rest! I really mean it, I've never encountered anything like this in terms of bed adherence.

I kept the settings to the Prusa defaults, which I've generally had a lot of luck with, so 60 degrees on the bed and 215 degrees on the hotend.

So far I've printed a brush holder, which is nice and shiny, and then thought I'd try some multimaterial prints.

The thing about multimaterial prints on the Prusa with the MMU2S, is that it has to repeatedly unload and load the filament into the nozzle. The 2 colour benchy at 0.1mm layers I printed, changed filaments 335 times during the print, the other filament used in it was Geeetech Marble.

If a filament is too stringy, too soft, snaps easily, or generally uneven, multimaterial prints like this are an utter nightmare, of failed loads followed by beeping for you to manually intervene.

I didn't have a single failed load during this print (or during the star trek bade, but that one was only a few loads). I'm really impressed!

And, to cap it all off, like the other Geeetech filaments I've tried, the price on this is definitely right.

6 mensen vonden dit nuttig

Vertaal recensie in het Nederlands

Jeff FreeMAN

La parfaite illusion du cuivre !!!

Beoordeeld in Frankrijk op 11 september 2019

Stijlnaam: A Silk CopperGeverifieerde aankoop

Bonjour à tous,

J’ai le plaisir de vous présenter une petite revue du filament GEEETECH SILK COPPER que j’ai testé pour vous.

Le colis m’est parvenu moins de 24h après ma commande sur AMAZON (prime). Le colis était parfaitement conditionné. La bobine étant sous blister et sous vide accompagnée d’un sachet de silicate anti-humidité. Après quelques vérifications au pied à coulisse numérique, j’ai pu constater que le filament a un diamètre régulier 1,75 mn (il est a noté qu’après l’utilisation complète de la bobine, aucun nœud ni boucle sont à signaler).

Concernant le filament, j’ai commencé mes essais par une tour de chaleur variant de 190° à 230°.

Aucune indication concernant les températures n’était inscrite sur la boite et la bobine.

Les résultats montrent que la température idéale se situe entre 205° et 215°.

Viennent ensuite les tests du lit d’impression : mes essais ont été effectués sur un miroir, entre 50° et 60° l’adhésion est parfaite. J’ai également entrepris une impression sur un lit non chauffé et là il s’avère que de la 3D lac est nécessaire pour une bonne prise de la première couche.

A propos des hauteurs d’impression, j’ai effectué des prints avec des hauteurs variables allant de 0,10 à 0,4 mm. Sur toute cette plage, je n’ai noté aucune difficulté d’impression et aucune occlusion de la buse. Il est cependant à noter que 0,10 mm soit la limite la plus basse avant d’éventuels bouchons ou jamm. (Ce filament comporte de fines particules de matière donnant l’aspect du cuivre).

En conclusion, le résultat de mes différentes impressions est bluffant et parfait. Chaque couche est parfaitement alignée et les petites particules donnant l’aspect cuivre lustré masquent totalement les stries des hauteurs de couche donnant un résultat parfaitement lisse comme du cuivre.

Dommage que GEEETECH n’est pas pensé à proposer des bobines en carton recyclable.

les prints ci dessous ont été réalisés sur une A20M ( TM2208 / Damper moteur / extruder Bondtech / marlin2 custom ) / température 215°/55°/ vitesse 60mms / slicer CURA 4 )

45 mensen vonden dit nuttig

Vertaal recensie in het Nederlands

Screedy

Silk Gold PLA that prints great and has a deep rich colour and shine

Beoordeeld in het Verenigd Koninkrijk op 1 augustus 2020

Stijlnaam: Silk GoldGeverifieerde aankoop

Ok, this is Silk Gold from Geetech

it has a very shiney and vibrant gold colour off the reel,good consistanct diameter over 150CM,well packaged (in a vacum seal bag with incandescent bag)

Print settings MK8 extruder with a Ultrabase Glass bed and Glue stick:
Nozzle: 193C
Bed: 55C
Flow: 96%
Cooling: 30-90%

prints great,smooth with little artifacts in comparison to other filiments i have used. there was minimal setup for a first print other than the usual you should be doing with all new roles (temp tower,speed test,flow rate)

all pictures posted are of prints that were done straight after each other with the above calibration and a glue stick on a glass bed.

theres no adhesion issues but i always use a glue stick and run a fucll filiment calibration on new rolls.
Layers are strong and bonded and with the temp test tower you can see it prints bridges very well

colour is vibrant with reddish undertones and a shiney finish (after printing its slightly dull but a "heat seal" with a heat gun or lick with a blow tourch brings the shine right back,just like PETG)

i would very much recomend this filiment if your printing something yellow or gold to catch the eye,and just for general printing.

yes take note of the negitive reviews also but also remember that calibration or your print settings and printer is almost 80% of the adhesion and print quality battle.

Een iemand vond dit nuttig

Vertaal recensie in het Nederlands

David A Jones

Silk Copper PLA Test

Beoordeeld in het Verenigd Koninkrijk op 2 november 2021

Stijlnaam: A Silk CopperGeverifieerde aankoop

De media kon niet worden geladen.

I initial bought this PLA due to the silk copper colour.
The filament is supplied vacuum packed and upon opening the reel the plastic is very neatly wound on the reel so no snagging or tangling!
The centre of the reel has a much larger diameter than most other reals do, the reel actually sat on the desk, I had to print a hub to go inside to fill up the reel to work in the holders I use, not a disaster, just a niggle but I will save the hub for future Geeetech reels.
Purging before printing gave a nice smooth feed with no spitting or popping so I expected good things.
I drew out about 5 metres of filament and measured the diameter in several places all within the stated specification.
My printer is a 7 year old Aworldnet A600 i3 clone, with an skr1.4 turbo upgrade, 0.4mm nozzle and BL Touch.
I used my default settings of bed 60 degrees, extruder 200 degrees and no fan for first 5 layers.
First layer was excellent, almost perfect, so I left it alone to print, after some time I returned and it was still printing with no failure and the overall finish looked excellent.
Once completed I removed the skull and checked it out in my mini photo booth, the quality of the print, even running with a later height of 0.3mm is excellent. The photos show the object looking very good, but the tactile feel is even better than the looks. It feels great in the hand and the copper finish is much better than I expected.
I have had some lovely coloured filaments in the past but sometimes good looking filaments don’t always print well.
This filament not only is well priced, it prints excellently and looks gorgeous. I think I may have to find what other amazing colours are available and give them a try too.

Vertaal recensie in het Nederlands

MIW

A lovely Copper Finish

Beoordeeld in het Verenigd Koninkrijk op 21 april 2022

Stijlnaam: A Silk CopperGeverifieerde aankoop

If you are looking for a great copper finish, then this is the one for you.

The PLA arrived in great packaging and also included an additional bag that is resealable to protect the PLA when not being used.

The copper finish is outstanding - the picture doesn't do it justice but it is a very high quality shiny finish.

I printed a temperature tower to get the right settings - which turned out to be 205c on the Hot End and because I have a glass plate I upped the bed temperature to 65c and that gave the best results and the best adhesion (Glass beds always require a slightly hotter setting).

There was no sign of clogging and the first layer went down perfect on my Geeetech A10.

I can recommend this for a great copper finish.

Vertaal recensie in het Nederlands

5 sterren		72%
4 sterren		14%
3 sterren		6%
2 sterren		3%
1 ster		5%

Selecteer uw cookievoorkeuren

GEEETECH PLA Silk filament 1,75 mm, 3D-printerfilament PLA 1 kg spool,...

›

Klantenrecensies

Klantenrecensies

GEEETECH PLA Silk filament 1,75 mm, 3D-printerfilament PLA 1 kg spool, wit, 1

Gefilterd op

Er is een probleem opgetreden tijdens het filteren van de recensies. Probeer het later opnieuw.

Vanuit Nederland

Er is een probleem opgetreden tijdens het laden van de opmerkingen. Probeer het later opnieuw.

Uit andere landen

Vragen? Snel antwoorden krijgen van recensenten

Selecteer uw cookievoorkeuren

GEEETECH PLA Silk filament 1,75 mm, 3D-printerfilament PLA 1 kg spool,... › Klantenrecensies

Klantenrecensies

GEEETECH PLA Silk filament 1,75 mm, 3D-printerfilament PLA 1 kg spool, wit, 1

Gefilterd op

Er is een probleem opgetreden tijdens het filteren van de recensies. Probeer het later opnieuw.

Vanuit Nederland

Er is een probleem opgetreden tijdens het laden van de opmerkingen. Probeer het later opnieuw.

Uit andere landen

Vragen? Snel antwoorden krijgen van recensenten

GEEETECH PLA Silk filament 1,75 mm, 3D-printerfilament PLA 1 kg spool,...

›

Klantenrecensies